Rail Embankments - Trains for Wargames part 5

With the flat track sections of the track now completed I turned my attention to the raised track. I had two considerations when putting this together, firstly the pieces should not be so large that storage would become an issue and secondly the embankments had to be sufficiently high enough to allow a vehicle to pass through (ie under a bridge)

As an example of rail bridge on embankment

 

I settled on the base of the embankments to be 16cm wide and the track top are to be 8cm wide. The height of the embankment would be 8cm high. This would mean the embankment itself would enjoy an angle of 45 degrees ie a slope ratio of 1 to 1.

I did investigate the slope angle before starting on this journey and discovered that embankments typically have a slope ratio of 1 to 4 or 1 to 5 – had I of gone with the former my base boards would have been close to 64 cm wide ! Not really an option.

Embankment Diagram

 

The embankments themselves were cut from polystyrene using my trusty foam cutter. I quickly realised that by cutting out the right length it bame very easy to angle the cutter at 45 degrees and then slice out the various sections.

As you can see from the photos below they are all quite uniform 

 

 

Once these were cut I glued them down onto hardboard bases. The bond between the base and polystyrene blocks was then strengthened with a hole being drilled in the reverse side and a bbq skewer driven in.

These ‘embankments are quite light and flimsy so strengthening was required. They were all given a good old coat of black acrylic paint. This not only seals the unit but also gives it a tough exterior coat.
 

 

 

The banks were then liberally coated in pva and then covered in sand. Once this was dry a second coat of acrylic paint was added – dark brown this time.

 

 

 

 

 

Sand cover banks

Brown paint over sand and top track laid with ballast

   

I built enough embankments to stretch 2 metres including a couple of curved sections to give a bit of variety. Given that they are going to dominate any landscape (an create a natural fortification) I quickly realised that a number of cut-through’s would need to be made – namely tunnels. So again using the foam cutter I created two of them. The inspiration for these is a nearby bridge to my home which also illustrates the height and steepness of the embankment.

 

 

The brick work around the edge of this tunnel has been created out of a thin skim of blue foam embossed with a pencil. The tunnels themselves are wide enough for a vehilcle pass through and are the same width as my other roads.

This facing was made using some old off cuts of embossed plasticard.

 

The other big feature is a bridge that can span my big rivers. This time I cut out the two end sections for the embankment and then built the bridge from pink foam (inside) and clad the outside in thicker blue foam. This meant I could give the top of the bridge a wall. As before the stonework was embossed on the foam with a pencil.

 

 

I should mention that when I cut out the span I created a foam sandwich and held all the pieces together using foam skewers – the shape of the arch came from the lid of an oval ice cream lid. The water effect was created using my trusted Oxford Blue Vinyl Floor Tiles sourced from Homebase. A walk way again the river edge has been added with blue foam and etched to create a slab effect (this way land troops can still use the tunnel as an cut through.

Some painted versions of the bridges...

 

 

 

 

 

Next up - greening the embankments.

 

First up I found my mixing bowl and poured in copious amounts of flock, static grass and what looks like really small bits of clump foliage. These all had different hues of green but when mixed together by hand create a great looking verdant cover.

Taking each embankment piece in turn I coated the exposed brown slopes with pva (lots of it) and then scattered the ground cover over the pva. Firmly pressing by hand the flock onto the glue. These were set aside to dry. Already the green slopes have given the embankments a wow factor!

 

Looking around at my local area where there are a number of these embankments its not uncommon for these to be wooded. So Ill be adding some trees then in time.

 

 

Had to put them on the table

 

 

 

So a few trees and bushes need to be added but otherwise they are good to go..

 

Until next time...